PT&P custom designed 16 G type constant spring supports for a power plant in Mississippi. The constants are comprised of two standard constant spring housing sub-assemblies joined together with an intermediate bridge assembly. They also include welded beam attachments, rods and hex nuts. The assemblies are designed to support pipes ranging from 80″ – 96″ in diameter. Standard load and travel tests were performed prior to shipment.
Read More
These insulated pipe supports are designed for 6″ diameter cold temperature piping for a gas refinery in Texas. They are fabricated with a carbon steel shell and 5″ thick polyurethane insulation. PT&P offers various types of insulated supports utilizing insulating materials designed for piping ranging in surface temperatures from -460°F to 1,200°F.
Read More
PT&P manufactured seventy-two bolt cradle pipe supports for a Sulphuric Acid Plant in Canada. The supports are designed for pipes ranging from 1-1/2″ to 20″ in diameter. They are fabricated from carbon steel and coated with a special protective paint for acid service. Standard bolt cradle supports are offered in 2″ to 24″ diameter pipe sizes; however, PT&P can manufacture any size needed for your application.
Read More
112 custom variable springs designed for a furnace application for an oil refinery in Venezuela. The furnace cans are designed from carbon steel and painted with red oxide primer to prevent corrosion when exposed to high temperatures. The sizes of these figures PTP-6 and PTP-8 range in length from 25″- 39″, with a total travel of 0.1″- 1.821″ and loads varying from 430 – 681 lb. A load test to confirm the spring rate was conducted on each assembly prior to shipment.
Read More
These pipe guides were designed for a recovery boiler in a power plant in Oklahoma. The guides were designed to control lateral pipe movement and maintain the alignment of the piping through its axial and contraction cycles. They were designed to support 6″, 12″ and 18″ pipes and range in length from 70″ – 120″. The assemblies were fabricated from carbon steel with a hot-dipped galvanized finish.
Read More
PT&P designed and manufactured 27 B-Type variable spring supports for an oil refinery in Louisiana. The spring cans, rods, welded beam attachments, turnbuckles and clevises are fabricated from carbon steel. The spring cans have a 12-3/4″ diameter and measure 290″ from the bottom of the steel to the connection of the pipe. They were designed for 2″ of vertical movement and operating loads between 24,375 and 27,500 lb.
Read More
Pipe Shields Inc., a division of PT&P, manufactured 215 heavy duty pre-insulated supports for a high temperature application in Oregon. They are 15″ L x 20″ W x 31″ H and are designed to accommodate 14″ – 20″ diameter pipes. The hot shoes have a calcium silicate insulation thickness of 2.5″- 3″. The base, clamps, nuts, jackets and bolts are all fabricated from hot dipped galvanized carbon steel and coated with red oxide paint. Standard Q.C. and dimensional tests were performed prior shipment.
Read More
PT&P designed and manufactured 282 instrument supports to support a six-drum coker unit in a refinery in Indiana. Some of the assemblies are designed to be bolted by anchor bolts while others are designed to be welded. The supports are fabricated from hot-dipped galvanized carbon steel and measure 11″ – 61″ in height and 5″ – 28″ in width.
Read More
PT&P designed sway strut and pipe clamp assemblies for a pipeline at a natural gas facility located in Canada. The sway struts are 87-1/2″ in length and the clamps are designed for pipes ranging from 6″ to 42″ in diameter. The assemblies are designed for operating loads ranging between 3,300 lb. to 20,000 lb., with an operating temperature of 392°F and 9mm -20mm of allocated vertical movement. A load test was performed on the assemblies prior to shipment.
Sweco Fab, Inc. (a division of PT&P) custom designed a transition piece weighing 6,000 lb. for a facility in Texas. The piece measures 48″ x 72″ x 72″ and is fabricated from carbon steel. It will be used to connect a round water tower to a square duct. Prior to shipping, the product was 100% dye penetrant tested.
Read More