List | Piping Technology & Products, Inc.

Pipe Shoes For 14" Pipe At A LNG Plant

November 30, 2001

Piping Technology & Products, Inc. fabricated cryogenic pipe supports designed for a 14-inch pipe at a LNG plant in Algeria. The pipe operates below minus 50 degrees F, therefore the pipe supports were fabricated from three different materials in order to accommodate the low temperatures. The upper part, which clamps on to the pipe, was fabricated from a stainless steel plate that retains its strength at low temperatures. The middle section is a laminated phenolic block made from layers of wood impregnated under vacuum with a synthetic resin. A crossed orientation of the hard wood fibers is used to provide extra strength. The laminated phenolic block, which is a poor conductor of heat, was bolted to the bottom plate of the galvanized carbon steel.

Are you in need of some cryogenic pipe supports for an upcoming project? Get pricing today!

Big Ton Springs With Loads Up To 450,600 Newtons

November 28, 2001

Piping Technology & Products, Inc. specially designed and fabricated Big Ton Variable Springs for a chemical project in Canada. The supporting beams are 30″ in length with PTFE, 25% glass filled stainless steel slide plates. The Big Ton Springs were designed with six coil springs with external guides to prevent horizontal twisting and internal guides to withstand horizontal friction forces. These units were also designed for operating loads from 260,000 to 350,000 Newtons and hydro-test loads from 300,000 to 450,600 Newtons. A total of six units were painted with a special finish specified by the client.

Need a big ton? Get pricing today!

1,728 Rods & Clevises

November 16, 2001

Piping Technology & Products, Inc. custom-designed and fabricated 1,728 rods and clevises for a heat recovery steam generation plant. The rods and clevises will be utilized to support various pipe loads throughout the piping system.

Learn more about rods and clevises by visiting our webinar archives!

Type F Variable Springs With Specially Made Locking Devices

November 3, 2001

Piping Technology & Products, Inc. specially designed twelve Type-F variable spring hangers (4-160-F, 8-170-F, 8-180-F) for an oil refinery in Indiana. These variable spring hangers were custom designed to support a Hydro-Test load 4.5 to 5 times the design load, which ranged from 7,988 lb. to 13,075 lb. The spring rates of the variable spring hangers ranged from 500 lb./in. to 750 lb./in. with travels of 1.15″ to 2.82″, upward movement respectively. The locking devices for these springs were manufactured using basic materials (rods, hex nuts and heavy pipe wall) and a special pressure plate to accommodate the application design criteria requested by the client. The base plate designed for these F- Type cans were modified to accommodate the locking devices.

Learn more about variable springs by visiting our webinar archives!

U-Type and F-Type Constant Spring Supports

October 30, 2001

Piping Technology & Products, Inc. designed, manufactured and delivered a total of 8 constants to a power plant in Mexico. The designs consisted of 4 Horizontal U-Types Upthrust (Figure 1) and 4 Vertical F-Types (Figure 2) that are to support 24-inch diameter pipes. Each consisted of different sizes. The constants are designed for loads of 2,839 lbs. to 8,963 lbs., for Total Travels ranging from 7 to 3 inches. Constants were painted CZ-11 per customer request.

Learn more about constant springs by visiting our webinar archives!

40" Diameter, Alloy Yoke Clamp

October 12, 2001

PT&P specially designed and manufactured a heavy duty, 40-inch diameter, alloy yoke clamp (cut from a 6″ thick plate) for a Power Plant in Mississippi. The clamp was designed for a 70,000 lb load and is to support a 40″ diameter, high pressure main steam line. The u-bolt was made of a 3″ diameter bar. In order to prove the design of this clamp, Finite Element Analysis was used to simulate the loads and stresses that it may experience in the field. The model shows the stresses at every point by a color coding system.

Want to learn more about yoke clamps and other types of clamps? Visit our webinar archives today!

Custom Pipe Support Assemblies For An Oil Refinery In Mexico

Piping Technology and Products designed and built 24 custom pipe support assemblies to meet the unusual needs of an oil refinery in Mexico. The pipe hanger assemblies each consisted of a 200 E-type constant spring support and a cradle assembly. The constants are designed for loads of 9856 lb. to 13,288 lb., and for total travels ranging from 3.5″ to 5.5″. Operational conditions dictated that the constant springs have settings for emergency and start-up, in additional to the standard settings of cold for shipping, and hot for normal operations.

The cradle assemblies attached to the constants are to support pipes with operational temperatures of 1070°F to 1100°F. Thus while the constants could be made of A-36 steel, the assemblies could not. The pipe saddle itself was made by splitting a section of A387-11 chrome alloy pipe. The other support components were all made of 304 stainless steel. This includes a 1-3/4″ Eye Rod, two 27″ I.D. U-bolts, and two 33″ lengths of 3″ diameter SCH. 80 pipe.

Do you need custom pipe supports for an upcoming project? Get pricing today!

Cryogenic Pipe Anchors For A Gas Refinery

October 2, 2001

Piping Technology & Products, Inc. manufactured cryogenic pipe anchors for gas refinery in Savannah, Georgia. The pipe anchors were fabricated with stainless steel and insulated with polyurethane foam. In order to prevent cold pumping, better known as temperature driven moisture penetration, polyurethane foam was poured around a stainless steel reinforcing pad. The ten cryogenic pipe anchors were fabricated to support 4-inch, 8-inch and 12-inch pipes. PT&P’s pre-insulated pipe supports department is devoted to the production of pipe insulation productions for both hot and cold applications.

Want more information on cryogenic pipe anchors? Visit our webinar archives today!

68" In Height Vertical Upthrust Constants

September 7, 2001

Piping Technology & Products, Inc. designed and built two, 68″ in height 100 U-Type constants for a power plant in Mexico. The vertical upthrust constants were designed to support 48,500 lb. each with a total upward travel of 3″. In order to prevent buckling of the constant housing, each constant was designed with five C7 x 14 3/4 lb. channels and a base plate of 26 3/8″ x 33 1/4″. These unique 100 U-Type upthrust constants were custom designed by PT&P to accommodate limited horizontal space requirement. The constants will be placed opposite to each other on a beam capable of supporting 99,000 lb. load of the pipe, plus the weight of the constants.

Want to learn more about constants? Visit out webinar archives today!

High Strength Stainless Steel Pipe Guides

August 23, 2001

Piping Technology & Products, Inc. manufactured over 2,000 high-strength, stainless steel pipe guides for a liquefied natural gas facility in Trinidad.

This high strength insulation is rare and mainly used for cryogenic applications. The guides range in a variety of sizes including 4-inch to 36-inch NPS and the fabrication included carbon steel base plates and stainless steel plates, nuts and bolts.

Looking for pipe guides? Get pricing today!

Our Subsidiaries

Blog